Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.

To visit the HydrostreamForums Knowledge Base CLICK HERE

Search found 9 matches

by bill6ft6
May 24, 2017 6:47 pm
Forum: Props, Setup, and Rigging
Topic: VOYAGER with 175 rude
Replies: 13
Views: 9094

Re: VOYAGER with 175 rude

what rpms are you running at 56? i've hit 68 now without chopper. 55 is where mine gets on the pad and is ready to open up. single biggest improvement was wedges (they are cheap) that improved my trim. got to noticing i had a rooster tail until getting on the pad which basically lifts nose and chang...
by bill6ft6
Mar 06, 2017 8:51 am
Forum: General Hydrostream Discussion
Topic: 1983 Hydrostream Voyager
Replies: 2
Views: 3872

Re: 1983 Hydrostream Voyager

when you drop throttle quickly, the steering torque reverses. i have voyager with 175, and years back buddy had same with 200 merc. don't really see need for hot foot on your boat, regulat throttle works fine. buddies would hit 77mph, no chine walking or bad habits
by bill6ft6
Mar 02, 2017 8:43 am
Forum: General Hydrostream Discussion
Topic: 1983 Hydrostream Voyager
Replies: 2
Views: 3872

Re: 1983 Hydrostream Voyager

surprised more knowledgable folks haven't responded to you. what you are experiencing is normal torque from the propeller. it will change with speed and trim angle. friend and i were playing around at about a 50 mph cruise and could steer the boat left or right with just trim adjustments. a tab on t...
by bill6ft6
Feb 28, 2017 10:47 am
Forum: Props, Setup, and Rigging
Topic: VOYAGER with 175 rude
Replies: 13
Views: 9094

Re: VOYAGER with 175 rude

I have a 5in manual jacking plate, and plan to try chopper again a little lower because it just cavitates. might get 200 merc in the spring. would perfer 225 but my rating is 200 and don't like insurance issues. buddy had a voyager with 200 merc and 28 chopper. no jacking plate, no lwp and he did 77...
by bill6ft6
Feb 27, 2017 10:57 pm
Forum: Props, Setup, and Rigging
Topic: VOYAGER with 175 rude
Replies: 13
Views: 9094

Re: VOYAGER with 175 rude

factory. from what i've read, under 80 ish, nosecones don't help. i keep water pressure at max trim
by bill6ft6
Feb 27, 2017 9:32 pm
Forum: Props, Setup, and Rigging
Topic: VOYAGER with 175 rude
Replies: 13
Views: 9094

Re: VOYAGER with 175 rude

ok, forget the 25 in shaft, i am a 20in. was mistaken. center of shaft is about 3.5 below pad. playing with props. marginal 14x26 and it ran 56 @5500. new 14.5 x 25 four blade ran 62.2@4700. next prop available is 14 1/8 x 23 4blade will be trying soon. I'm wide open to suggestions and info. should ...
by bill6ft6
Sep 03, 2016 3:00 pm
Forum: Props, Setup, and Rigging
Topic: VOYAGER with 175 rude
Replies: 13
Views: 9094

VOYAGER with 175 rude

I hear you, but replacing motors and lower units is too expensive, looking for other alternatives
by bill6ft6
Sep 03, 2016 11:59 am
Forum: Props, Setup, and Rigging
Topic: VOYAGER with 175 rude
Replies: 13
Views: 9094

VOYAGER with 175 rude

just got this boat and trying to get a handle to getting the set up right. has 25" shaft but manual jacking with 5" set back. motor and jack both maxed up in height. center of shaft is about 3.5 below pad. playing with props. marginal 14x26 and it ran 56 @5500. new 14.5 x 25 four blade ran...
by bill6ft6
Sep 03, 2016 11:31 am
Forum: Props, Setup, and Rigging
Topic: Factory OMC set back
Replies: 5
Views: 3919

Factory OMC set back

was called the "SeaDrive system". never caught on but I feel it was a precursor to the bracket systems used now