Oscillating tool would work for core removal.
[ Post made via Android ]
Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
Search found 327 matches
- Jun 09, 2018 8:46 am
- Forum: General Hydrostream Discussion
- Topic: New project VAMP, need input
- Replies: 15
- Views: 12105
- Jun 08, 2018 2:10 pm
- Forum: General Hydrostream Discussion
- Topic: New project VAMP, need input
- Replies: 15
- Views: 12105
Re: New project VAMP, need input
Are you taking pics with a camera or cell phone? You should be able to change the camera settings on your phone to take smaller resolution photos if that's what you're using.
[ Post made via Android ]
[ Post made via Android ]
- Jun 06, 2018 9:42 pm
- Forum: Introductions
- Topic: New To The Forum
- Replies: 2
- Views: 3522
Re: New To The Forum
Welcome to the forum. Lots of info here for you to absorb while you're stuck on land...and guide you on what you'll need to know when you're ready to buy your first Stream.
[ Post made via Android ]
[ Post made via Android ]
- Jun 06, 2018 9:34 pm
- Forum: Restorations, WIP, Makeovers
- Topic: 1980 Viper Rebirth
- Replies: 121
- Views: 85321
Re: 1980 Viper Rebirth
June 2nd-June 6th, 2018: After letting the transom cure for a few days, it was time to fine-tune the fitting. http://www.adadk.ca/viper/June06-18/KIMG0279.jpg I used a circular saw to bevel the bottom edge of the transom to match the angle. http://www.adadk.ca/viper/June06-18/KIMG0273.jpg http://ww...
- Jun 05, 2018 6:05 am
- Forum: Engine Tech
- Topic: 200 efi problems
- Replies: 6
- Views: 9283
Re: 200 efi problems
Do you run regular gas or premium? these motors hate ethanol, which is usually added to 87/89 octane gas.
[ Post made via Android ]
[ Post made via Android ]
- Jun 03, 2018 6:18 pm
- Forum: Engine Tech
- Topic: 200 efi problems
- Replies: 6
- Views: 9283
Re: 200 efi problems
Dirty injectors are common. Unfortunately fuel injector cleaning kits can be several hundred dollars so you might as well take it to a shop, if that's the issue. That's why I made suggestions on what you can try...to eliminate each potential cause. [ Post made via Android ] http://www.hydrostreamfor...
- Jun 03, 2018 4:46 pm
- Forum: Upcoming events or gatherings
- Topic: OPBRA 2018 dates...
- Replies: 2
- Views: 6648
OPBRA 2018 dates...
http://opbra.ca/wp-content/uploads/2017/02/OPBRA-Logo-500x405.png http://opbra.ca/wp-content/uploads/2017/02/OPBRA-Web-shots8-300x169.jpg http://opbra.ca/wp-content/uploads/2017/02/DSC_0246-300x200.jpg 2018 Race Dates and Sites Race #1 - The Deseronto Classic Cup Boat Races, Deseronto, Ontario, Jul...
- Jun 02, 2018 7:47 pm
- Forum: Engine Tech
- Topic: 200 efi problems
- Replies: 6
- Views: 9283
Re: 200 efi problems
Could be any number of issues.... Check the fuel filter on the engine, and if you have one on your fuel line, that too. Drain the VST to remove possibility of water/debris that might be in it. Check your sparkplugs. Check the ignition coil. When was the last compression test on the cylinders? Do you...
- May 26, 2018 9:42 pm
- Forum: Fiberglass and Composites Discussion
- Topic: DIY Resin Trap for vacuum infusion/bagging.
- Replies: 1
- Views: 4291
DIY Resin Trap for vacuum infusion/bagging.
When I'm ready to lay down my balsa core, I'm going to experiment with resin-infusing my core to see if it's viable. My vacuum pump is a 1/3rd HP 4CFM Ebay special. I plan on just doing a small piece first, say 1 foot by 1 foot. I know this wasn't needed, but I like building contraptions. Perhaps my...
- May 26, 2018 8:51 pm
- Forum: Restorations, WIP, Makeovers
- Topic: 1980 Viper Rebirth
- Replies: 121
- Views: 85321
Re: 1980 Viper Rebirth
Saturday May 26th 2018: Measured and cut my transom today. Using 3/4" marine-grade 13-ply BS1088 plywood. Using a straight-edge, I penciled on a 2 inch square grid. http://www.adadk.ca/viper/May26-2018/KIMG0271.jpg I then proceeded to drill holes as per the grid with a 1/8th inch bit.. http://...