Hey guys,
I have a new to me 1979 Vector, 1994 Merc 150hp Black Max, 5.5" CMC Manual jackplate, 14" X 26 pitch through hub exhaust Laser II prop. Prop shaft approx 2" below pad, 20 gallon fuel tank and battery in the back. Same problems as I read of on here, severe porpoise at mid speeds and a bad chine walk at top speed. The boat will get up and fly on the pad for a few seconds and then fall off and start chine walking. Any advice on where to start with my setup?
Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
Typical Vector issues. Need help.
-
- The new guy
- Posts: 2
- Joined: Nov 11, 2012 3:14 pm
- Location: Houston
- Contact:
-
- Hydrostream know it all
- Posts: 527
- Joined: Aug 08, 2011 10:22 pm
- Location: Peterborough Ontario
- Has thanked: 11 times
- Been thanked: 34 times
- Contact:
Re: Typical Vector issues. Need help.
Get the motor up at least an inch, that's a good place to start. Might not change porpoise but will help with chine walk. I put a drag plate on mine, a Vision with a 200 Merc on it. That almost eliminated the porpoise immediately. Mine's shorter than a Vector though, you might not have the same results as me...
[ Post made via iPhone ]
[ Post made via iPhone ]
1988 Canadian Edition Vision Sold
1990 Hydrostream Virage Stage 3 Turbo
1990 Hydrostream Virage Stage 3 Turbo
-
- The new guy
- Posts: 2
- Joined: Nov 11, 2012 3:14 pm
- Location: Houston
- Contact:
Re: Typical Vector issues. Need help.
Raised the motor up even with the pad. Boat runs MUCH better! Now I just need to learn how to drive the dang thing. The boat ran 68 at 5,600 rpm. Good? Bad? Ugly?
-
- HSF Lifetime Supporter
- Posts: 901
- Joined: Apr 11, 2010 12:57 pm
- Location: beaumont, tx
- Has thanked: 23 times
- Been thanked: 5 times
- Contact:
Re: Typical Vector issues. Need help.
get you a chopper prop...... trim it up and let her fly
[ Post made via Android ]
[ Post made via Android ]
81 vector....complete restore....1991 7 pedal 200 slightly modded
ALWAYS under construction
HYDROSTREAM HELLIONS
https://www.youtube.com/watch?v=YHE8wWZsFpw
ALWAYS under construction
HYDROSTREAM HELLIONS
https://www.youtube.com/watch?v=YHE8wWZsFpw
-
- Hydrostream Addict
- Posts: 420
- Joined: Apr 07, 2009 6:50 pm
- Location: Fairfield, CT
- Been thanked: 9 times
- Contact:
Re: Typical Vector issues. Need help.
Boat should run mid to upper 70's with a 26 Chopper. You need solid motor mounts, tight dual cable steering, a good CORE, a competition life jacket, kill switch with lanyard, and a foot throttle. Then raise the motor another inch and go lookin for 80.
transomstand
Original owner 1975 Ventura II SE
Original owner 1975 Ventura II SE
-
- Random Topics
- Replies
- Views
- Last post
-
- 4Replies
- 4753 Views
- Last post by Valero 86
Aug 25, 2017 9:25 pm
-
-
Missouri guy looking for the right blue flake project stream
Last post by AndrewZ « Aug 28, 2017 7:31 am - 3Replies
- 7315 Views
- Last post by TexasVector79
Dec 17, 2021 11:55 pm
-
-
- 5Replies
- 3982 Views
- Last post by AdamDK
Aug 30, 2017 10:42 am
-
- 8Replies
- 14812 Views
- Last post by AdamDK
Oct 15, 2023 9:22 am
-
-
Peterborough, Ontario Powerboat Races Sept. 16 & 17th 2017
Last post by AdamDK « Sep 10, 2017 8:48 pm - 1Replies
- 8125 Views
- Last post by AdamDK
Sep 10, 2017 8:48 pm
-
Who is online
Users browsing this forum: No registered users and 65 guests