Welcome to HydrostreamForums.com
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.

Registering only takes a few minutes and you can do so by CLICKING HERE

If you are a member, don't forget to log in to take full advantage of the forum.

1987 Hydrostream Voyager

Have questions about setting up your boat? Engine height, setback, prop, etc.
Post Reply
User avatar

Topic Author
wheely
The new guy
The new guy
Posts: 3
Joined: Oct 09, 2014 8:18 pm
Location: canada

1987 Hydrostream Voyager

Post by wheely » Oct 15, 2014 4:58 am

thinking of putting a jack plate just wondering which setback would be the best putting a new 200 ETEC Ho thank you

[ Post made via Android ] Image

User avatar

Fairwindracing
The new guy
The new guy
Posts: 6
Joined: Oct 16, 2014 9:48 pm
Location: Marblehead ma

Re: 1987 Hydrostream Voyager

Post by Fairwindracing » Oct 17, 2014 10:57 am

good to see an evinrude comeback!

User avatar

Surface Scratcher
Hydrostream Addict
Hydrostream Addict
Posts: 330
Joined: Apr 11, 2009 11:17 pm
Location: Central Texas

Re: 1987 Hydrostream Voyager

Post by Surface Scratcher » Oct 18, 2014 8:15 pm

Welcome,

For top speed?
Without knowing anything else about your setup, the answer is a lot.
Both the Vpad and XT will take 10 or more, maybe a little less with a heavy motor. :up:

User avatar

Rut311969
Hydrostream know it all
Hydrostream know it all
Posts: 584
Joined: Oct 25, 2010 9:03 am
Location: Burlington IA

Re: 1987 Hydrostream Voyager

Post by Rut311969 » Oct 19, 2014 4:53 pm

Im running a 225 ho etec with no set back and no modds and hitting 76-78 mph 85 Voyager.

User avatar

Topic Author
wheely
The new guy
The new guy
Posts: 3
Joined: Oct 09, 2014 8:18 pm
Location: canada

Re: 1987 Hydrostream Voyager

Post by wheely » Nov 02, 2014 8:09 pm

what prop you running with your 225 Ho

User avatar

Newowner20
The new guy
The new guy
Posts: 8
Joined: Oct 02, 2015 9:11 pm
Location: Winnipeg manitoba

1987 Hydrostream Voyager

Post by Newowner20 » Oct 03, 2015 10:37 am

Just bought a 82 voyager 150 merc mounted direct onto transom at lowest setting, need some advice for props, I have a 17 and 25 pitch laser prop at the moment but would like to find a good all around prop 3-4 or five blade?

[ Post made via iPhone ] Image

User avatar

terry2
The new guy
The new guy
Posts: 12
Joined: Sep 22, 2015 12:56 pm
Location: Wisconsin

1987 Hydrostream Voyager

Post by terry2 » Oct 03, 2015 10:32 pm

83 voyager 200 merc.25p 4 blade trophy 68-69 gps

User avatar

Newowner20
The new guy
The new guy
Posts: 8
Joined: Oct 02, 2015 9:11 pm
Location: Winnipeg manitoba

1987 Hydrostream Voyager

Post by Newowner20 » Oct 04, 2015 1:41 pm

How is it out of the hole with that prop

[ Post made via iPhone ] Image

User avatar

terry2
The new guy
The new guy
Posts: 12
Joined: Sep 22, 2015 12:56 pm
Location: Wisconsin

1987 Hydrostream Voyager

Post by terry2 » Oct 04, 2015 8:17 pm

hits hard out of the hole,on plane like right now.guy I bought the boat off of had a 26p chopper no jack plate was ok but I think I get better performance with this prop.these boats like the prop shaft about 2 1/2 inches below the pad.i had to raise my motor when I got the boat guy had it over 4 inches below the pad world of difference.lot of info on hydrostream.org on set ups on voyager,good luck :mrgreen:

User avatar

Newowner20
The new guy
The new guy
Posts: 8
Joined: Oct 02, 2015 9:11 pm
Location: Winnipeg manitoba

1987 Hydrostream Voyager

Post by Newowner20 » Oct 07, 2015 10:53 am

Thanks for the info, was considering raising the motor

[ Post made via iPhone ] Image

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest