Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.

To visit the HydrostreamForums Knowledge Base CLICK HERE

Need Viper advice

Have questions about setting up your boat? Engine height, setback, prop, etc.
User avatar

Topic Author
ViperMan
The new guy
The new guy
Posts: 13
Joined: Oct 06, 2013 9:06 pm
Location: Toronto, Ontario
Contact:

Need Viper advice

Post: # 21094Post ViperMan »

Hey guys!
Hope everyone's enjoying their summer, out on their boats and such... :boating:
Anyways, I've got my viper, lower end was just rebuilt, and motor was looked at, so I'm not worried about that 8-)
BUT, after the motor work, I took the jackplate taken off, it was a 6 inch, and I was told for a viper that's too much.
So I went to drive the boat, and the engine is running better then ever, but my setup is wrong.
My top speed has dropped,
More of the boat is in the water then before, even trimmed up. :cry:
My top speed used to be 55mph ( but it chine walked)
I put the fin on it = 48mph
Removed jack plate =44mph


So what I'm asking from you experts!
What is it I need to do to get my viper rippin better than ever! But still drivable( without chine walk, porposing)
Because I know it should/can go faster :up:

Prop is a 23p
Motor is a 115hp mercruiser
Please, any info is helpful, I've been struggling getting this boat setup for a while now, and getting somewhat frustrated.
Thanks again :!:

[ Post made via iPhone ] Image
Attachments
image.jpg
image.jpg (118.61 KiB) Viewed 4659 times
User avatar

Topic Author
ViperMan
The new guy
The new guy
Posts: 13
Joined: Oct 06, 2013 9:06 pm
Location: Toronto, Ontario
Contact:

Re: Need Viper advice

Post: # 21095Post ViperMan »

[ Post made via iPhone ] Image
Attachments
image.jpg
image.jpg (123.65 KiB) Viewed 4658 times
User avatar

Surface Scratcher
Hydrostream Addict
Hydrostream Addict
Posts: 344
Joined: Apr 11, 2009 11:17 pm
Location: Central Texas
Has thanked: 1 time
Contact:

Re: Need Viper advice

Post: # 21096Post Surface Scratcher »

Don't be frustrated, working on the set up is half the fun.

It would help to have more info... where is the prop shaft in relation to the pad, what are your rpms, what type of prop?

Could your gear ratio have been changed when the lower unit was rebuilt?

Meanwhile, here's a page that will discuss a lot of Viper set ups :up: http://hydrostream.org/TechTalk/TechTalk.htm
User avatar

Topic Author
ViperMan
The new guy
The new guy
Posts: 13
Joined: Oct 06, 2013 9:06 pm
Location: Toronto, Ontario
Contact:

Re: Need Viper advice

Post: # 21106Post ViperMan »

Thanks for the reply!
Prop shaft is about 3 inches below the pad.
Rpms- not sure because gauge just stopped working
Prop is a 23p, 3 blade stainless
And no, I don't think gear ratio was changed.
Thanks for the link, I'll check it out

[ Post made via iPhone ] Image
User avatar

Hippie459MN
Site Admin
Site Admin
Posts: 3966
Joined: Mar 25, 2009 7:31 pm
Location: Nowthen, MN
Has thanked: 346 times
Been thanked: 80 times
Contact:

Re: Need Viper advice

Post: # 21108Post Hippie459MN »

ViperMan wrote:Thanks for the reply!
Prop shaft is about 3 inches below the pad.
WOAH!!! Get that motor WAY up. 3 inches below the pad will make that boat handle like poo. Get it up to at least in inch below, and assuming you do not have a low water pick up on that, raise it up until you just start to loose water pressure. You will notice a HUGE difference in the way the boat will behave.

I hate to be the one to ask but has the core (not the floor) ever been replaced in it?
-Kevin
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet

1977 HydroStream Vulture - Worlds longest ongoing project. :eek:
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
User avatar

Topic Author
ViperMan
The new guy
The new guy
Posts: 13
Joined: Oct 06, 2013 9:06 pm
Location: Toronto, Ontario
Contact:

Re: Need Viper advice

Post: # 21111Post ViperMan »

Hey Hippie459MN
thanks for the helpful info, i figured this is a large part of the issues im having. Do you think i should get a 2" - 4" jack plate?
And im honestly not sure if the core was replaced, i assume not, because the previous owner didn't mention anything. Is there an easy way to tell if its had work on?
Thanks again
User avatar

aaron78viper
Regular
Regular
Posts: 173
Joined: Jun 03, 2012 8:29 pm
Location: MA
Been thanked: 6 times
Contact:

Re: Need Viper advice

Post: # 21141Post aaron78viper »

whoa there, don't jack the motor up just yet, you need to make sure that thing has cooling water to the motor. you can only run the propshaft even with the pad if you have a low water pickup. Do you have a lwp?
User avatar

carson
The new guy
The new guy
Posts: 8
Joined: Jun 27, 2015 12:09 pm
Location: Barrie Ontario Canada
Contact:

Need Viper advice

Post: # 21216Post carson »

Get some dual steering on that baby to. These boat need to be driven, when they start getting up on the pad you need to keep it balanced or it will chine walk. Sloppy steering and rubber mounts will also make it hard to control. My valero is fairly easy to keep on the pad but if you dont keep up on the steering it will start to flop around lol

[ Post made via iPhone ] Image
User avatar

transomstand
Hydrostream Addict
Hydrostream Addict
Posts: 420
Joined: Apr 07, 2009 6:50 pm
Location: Fairfield, CT
Been thanked: 9 times
Contact:

Need Viper advice

Post: # 21218Post transomstand »

What year is the motor?
transomstand
Original owner 1975 Ventura II SE
Post Reply

  • Random Topics
    Replies
    Views
    Last post

Who is online

Users browsing this forum: No registered users and 11 guests