Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
76 Hydrostream Ventura II SE - Restore Project
Re: 76 Hydrostream Ventura II SE - Restore Project
Well, I'm about done with the floor, just have some minor cleanup around the edges. I have not seen any detailed pics of a Ventura core removed, is it just the stringers and the space between them, or does it extend outside of the stingers? I guess i will take your advice regarding removing the core, I don't think it should be too much work, compared to removing the entire floor..
- Attachments
-
- week10a.jpg (459.83 KiB) Viewed 8779 times
Re: 76 Hydrostream Ventura II SE - Restore Project
Getting started on removing core. I have a 2"X10"X10' setup under the pad, and the trailer seems to be holding things together fine, I am wondering if i need any additional support when i start getting more of the core removed?
- Attachments
-
- week10d.jpg (723.5 KiB) Viewed 8761 times
-
- week10c.jpg (441.23 KiB) Viewed 8761 times
-
- week10e.jpg (640.69 KiB) Viewed 8761 times
-
- Hydrostream know it all
- Posts: 997
- Joined: Nov 20, 2009 11:35 pm
- Location: Pleasant Prairie, WI
- Been thanked: 2 times
- Contact:
Re: 76 Hydrostream Ventura II SE - Restore Project
Now you are getting somewhere. Look at all that rot. The stringers are half gone too. Take it all out until all that's left is a smooth fiberglass bottom from transom to bow. I'd do the transom at the same time. From the looks of it, it needs to be done too.
Bill
Bill
Re: 76 Hydrostream Ventura II SE - Restore Project
Yes, Transom is coming out.. there will be nothing but the fiberglass shell when it's done.
-
- Hydrostream know it all
- Posts: 997
- Joined: Nov 20, 2009 11:35 pm
- Location: Pleasant Prairie, WI
- Been thanked: 2 times
- Contact:
Re: 76 Hydrostream Ventura II SE - Restore Project
That's good. It's more work, but in the end you'll have a safe boat that will last at least another 40 years. My Ventura II and Viking projects are on hold for the summer while I boat, but will start them back up here in a couple of weeks. I'll try to post some pictures of mine when I get back into them. For now, it's just enjoying the Vulture.
Bill
Bill
Re: 76 Hydrostream Ventura II SE - Restore Project
Almost done with core, I left the front part in so I could have more support while taking out the steering wheel, cables (going to hydraulic steering), and gauges. Now I only have the front 1/3 of the core to remove. After removing the core, I should be ready to get some work done. I found somewhere to do my transom and since they are more experienced than me with fiberglass, they will do the transom, core, floor and gel coat repairs. So, I guess i will move on to the motor. I was thinking of doing a rebuild kit for the 77 Evinrude 140. I will also have to start looking for a good jack-plate (probably just a regular manual with 6" of travel). Going back in with interior, I was thinking of two buckets in the front and a bench in the rear up against the spalsh well, incorporating a ski pole into that same area.. Well, I have a bunch of ideas, but don't know for sure what i will do yet..
- Attachments
-
- week11c.jpg (409.1 KiB) Viewed 8717 times
-
- week11b.jpg (566.48 KiB) Viewed 8717 times
-
- week11a.jpg (518.13 KiB) Viewed 8717 times
Re: 76 Hydrostream Ventura II SE - Restore Project
I know this isn't the right forum, and I have posted this in the "Fiberglass and Composites Discussion" forum, but just wanted to know if anyone had used this for re-coring ?
I was wondering if anyone has ever seen or used SphereCore SBC?
http://www.carbon-core.com/spheretex-sp ... re-SBC.htm - Link to site
https://www.youtube.com/watch?v=fxRu93VnhTs - Link to video
I was wondering if anyone has ever seen or used SphereCore SBC?
http://www.carbon-core.com/spheretex-sp ... re-SBC.htm - Link to site
https://www.youtube.com/watch?v=fxRu93VnhTs - Link to video
76 Hydrostream Ventura II SE - Restore Project
Finally got some updated pics.. having transom and core done.
- Attachments
-
- floor2.jpg (166.75 KiB) Viewed 8514 times
-
- transom2.jpg (175.91 KiB) Viewed 8514 times
-
- transom.jpg (203.66 KiB) Viewed 8514 times
-
- floor1.jpg (182.38 KiB) Viewed 8514 times
-
- Random Topics
- Replies
- Views
- Last post
-
- 4Replies
- 4573 Views
- Last post by RussF
Jun 02, 2012 5:55 pm
-
- 11Replies
- 6989 Views
- Last post by Fly N By
May 25, 2012 4:02 pm
-
- 4Replies
- 3512 Views
- Last post by coupe427
May 17, 2012 4:40 pm
-
- 6Replies
- 4796 Views
- Last post by silkeysak
Jun 01, 2012 6:51 pm
-
- 24Replies
- 27915 Views
- Last post by YDOC462
Sep 23, 2013 7:40 pm
Who is online
Users browsing this forum: No registered users and 3 guests