Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.

To visit the HydrostreamForums Knowledge Base CLICK HERE

Newbie needs advice.

The place for all general Hydrostream discussions.
User avatar

Topic Author
Kuzer
The new guy
The new guy
Posts: 8
Joined: Sep 29, 2020 3:06 pm
Location: Butler, TN
Been thanked: 1 time
Contact:

Newbie needs advice.

Post: # 25026Post Kuzer »

Hello everyone! I'm a newbie and just purchased a 1989 Vulture XT from Aaron Wachholz. It has a built 225 Yamaha by Eco-tech putting out 340 HP. I bought the boat sight unseen and arranged delivery. I have never driven a Hydrostream before but have had many boats in the past but none or this caliber. I understand this boat went 96 mph but the driver was very experienced. I have no desire to go that fast, at least not now until I can get use to it. My question is can I tame it down for now by adjusting the jack plate? Again unfamiliar with these types of boats and have never been over 65mph in a boat. I did take it out but did not get it planed. The temp light was flashing so I called it a day. I have been reaing the forums trying to learn but understand these boats can be dangerous with an inexperienced driver. Any suggestions of progression? Thank you in advance for any advice.
User avatar

265mercman
Hydrostream Addict
Hydrostream Addict
Posts: 418
Joined: Jun 22, 2010 5:22 pm
Location: hohenwald, tn
Contact:

Re: Newbie needs advice.

Post: # 25027Post 265mercman »

These boats are a hand full to drive the best way to learn to drive it is seat time if the motor is werre it was at 96 leave it dont move it.. start out get it on plane and slowly get it up to speed the chine walk side to side movement goes left steer right slightly u feel it come back to center fall right steer left slightly till u figure out how to keep it in the center more trim more movement .. but once u hit the sweetspot if its like mine a 90+ has no movement hardly like butter

[ Post made via Android ] Image
79 vector missing in action!!!!!

2006 vking center steer
User avatar

Topic Author
Kuzer
The new guy
The new guy
Posts: 8
Joined: Sep 29, 2020 3:06 pm
Location: Butler, TN
Been thanked: 1 time
Contact:

Re: Newbie needs advice.

Post: # 25028Post Kuzer »

Thanks! Appreciate the response. Just want to be safe.

[ Post made via Android ] Image
User avatar

Topic Author
Kuzer
The new guy
The new guy
Posts: 8
Joined: Sep 29, 2020 3:06 pm
Location: Butler, TN
Been thanked: 1 time
Contact:

Re: Newbie needs advice.

Post: # 25029Post Kuzer »

Thanks! Appreciate the response. Just want to be safe.

[ Post made via Android ] Image
User avatar

tnelson77
Regular
Regular
Posts: 106
Joined: Aug 01, 2018 11:05 am
Location: Minneapolis Minnesota
Has thanked: 151 times
Been thanked: 50 times
Contact:

Re: Newbie needs advice.

Post: # 25030Post tnelson77 »

Read the "Allison Red Book" for how to handle a high performance V hull. While Allisons and Hydrostreams are different designs, a lot of it carries over.
User avatar

Topic Author
Kuzer
The new guy
The new guy
Posts: 8
Joined: Sep 29, 2020 3:06 pm
Location: Butler, TN
Been thanked: 1 time
Contact:

Re: Newbie needs advice.

Post: # 25031Post Kuzer »

Will give it a try, thx.

[ Post made via Android ] Image
User avatar

idvette
Hydrostream know it all
Hydrostream know it all
Posts: 527
Joined: Aug 08, 2011 10:22 pm
Location: Peterborough Ontario
Has thanked: 11 times
Been thanked: 34 times
Contact:

Re: Newbie needs advice.

Post: # 25033Post idvette »

I wouldn't try changing setup unless there was something seriously wrong. The fastest setup is usually very close to the safest setup. Find someone in your area that is experienced and let them take you out for a drive, will probably be your best learning experience. And it's Hydro Tech, not Eco tech lol

[ Post made via Android ] Image
1988 Canadian Edition Vision Sold
1990 Hydrostream Virage Stage 3 Turbo
User avatar

Topic Author
Kuzer
The new guy
The new guy
Posts: 8
Joined: Sep 29, 2020 3:06 pm
Location: Butler, TN
Been thanked: 1 time
Contact:

Re: Newbie needs advice.

Post: # 25034Post Kuzer »

Thanks

[ Post made via Android ] Image
User avatar

Hippie459MN
Site Admin
Site Admin
Posts: 3969
Joined: Mar 25, 2009 7:31 pm
Location: Nowthen, MN
Has thanked: 349 times
Been thanked: 80 times
Contact:

Re: Newbie needs advice.

Post: # 25036Post Hippie459MN »

I have personally seen that Vulture. You got a SWEET boat there. Did it stay local, or here in Minnesota I should say?

[ Post made via Android ] Image
-Kevin
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet

1977 HydroStream Vulture - Worlds longest ongoing project. :eek:
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
User avatar

Topic Author
Kuzer
The new guy
The new guy
Posts: 8
Joined: Sep 29, 2020 3:06 pm
Location: Butler, TN
Been thanked: 1 time
Contact:

Re: Newbie needs advice.

Post: # 25038Post Kuzer »

Thanks! No it is now on Watauga lake in NE Tennessee.

[ Post made via Android ] Image
Post Reply

  • Random Topics
    Replies
    Views
    Last post

Who is online

Users browsing this forum: No registered users and 24 guests