I have the core and stringer work completed and have started looking at the floor.
I expected the main floor would be more or less flat. It's not.
The middle 6' of the 8' long floor is pretty flat. The front end curves upwards 1" on the port side and and 1/2" on the starboard side. It also kicks up at the transom, but not as severely.
It is an 89 V-King and I am using 1/2" marine grade plywood for the floor.
I think the port/starboard discrepancy is caused by a previous repair on the port side.
No point asking if this curve is normal because it is what it is.
I am wondering about installing the floor.
With the naked plywood (not sealed), the curves are achievable with modest weight. But it needs to be sealed, right?
I am wondering about sealing the bottom of the floor and then bending it in tension. Polyester resin will possibly crack and then we have lost the seal.
How are other prepping the bottom side of the plywood? Resin, resin and glass, other?
Does the floor need to be in one piece? 3 pieces would lay pretty.
Maybe put a couple of 1/4" deep score cuts across the bottom?
Welcome to HydrostreamForums.com
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
V-King Floor
-
- Getting my feet wet
- Posts: 24
- Joined: Jul 12, 2022 10:41 am
- Location: Oshawa, Ontario
- Has thanked: 1 time
- Been thanked: 1 time
-
- Regular
- Posts: 181
- Joined: Jun 03, 2012 8:29 pm
- Location: MA
- Been thanked: 11 times
Re: V-King Floor
Some of the floor in my vipers were curved. I believe it was required to fit into the strakes, where the hull begins to curl upward. also, in order to manufacture quickly, i can imagine there would be some differences from one to the next. Grinding the perfect floor shape takes time. Just do your best.
-
- Site Admin
- Posts: 3991
- Joined: Mar 25, 2009 7:31 pm
- Location: Nowthen, MN
- Has thanked: 358 times
- Been thanked: 83 times
- Contact:
Re: V-King Floor
My Vulture the floor sits perfectly flat. Which has the almost the exact same core, stringer, floor layout as the Vking.
-Kevin
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
-
- Random Topics
- Replies
- Views
- Last post
-
- 8Replies
- 58232 Views
- Last post by coupe
May 11, 2009 6:37 am
-
- 4Replies
- 40562 Views
- Last post by Enticer1
May 14, 2009 11:36 am
-
- 2Replies
- 35934 Views
- Last post by king gill
May 17, 2009 5:35 pm
-
- 8Replies
- 53003 Views
- Last post by Keuka Vegas
May 17, 2009 7:34 pm
-
- 7Replies
- 48715 Views
- Last post by Vegas XT
May 20, 2009 8:04 pm